Problems with a Voice Gateway.
Printed From: CertCities.com Forums
Forum Name: CCIE
Forum Discription: Discuss the CCIE written and lab here.
URL: http://certcities.com/forums/forum_posts.asp?tid=5163
Printed Date: 23 October 2007 at 3:24pm
Topic: Problems with a Voice Gateway.
Posted by: hudsonmbg
Subject: Problems with a Voice Gateway.
Date Posted: 09 July 2007 at 11:38pm
| Hi I have another problem. I guess I am always having issues. Well, I have a Cisco Voice Gateway connected to an Ericsson switch. When I dial local calls with 13 digits including the country code, the call goes through but when we dial an International call, the Ericson switch drops the calls. Let me attach the output of the debug commands and the router configuration. IS there a command to specify the end string so that the switch knows the last digit and forwards the call? This is quite bulky. isdn switch-type primary-net5 ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! controller E1 3/0 pri-group timeslots 1-31 ! controller E1 3/1 pri-group timeslots 1-31 ! controller E1 3/2 pri-group timeslots 1-31 ! controller E1 3/3 pri-group timeslots 1-31 ! ! ! interface GigabitEthernet0/0 description "TOWARDS PABX LAN" ip address 10.10.12.1 255.255.254.0 duplex auto speed auto negotiation auto ! interface GigabitEthernet0/1 ip address 192.168.101.29 255.255.255.0 duplex auto speed auto negotiation auto no cdp enable ! interface Serial0/0 no ip address shutdown clock rate 2000000 no fair-queue ! interface Serial0/1 no ip address shutdown clock rate 2000000 ! interface Serial3/0:15 no ip address encapsulation hdlc isdn switch-type primary-net5 isdn incoming-voice modem isdn bchan-number-order ascending no cdp enable ! interface Serial3/1:15 no ip address encapsulation hdlc isdn switch-type primary-net5 isdn incoming-voice modem isdn bchan-number-order ascending no cdp enable ! interface Serial3/2:15 no ip address encapsulation hdlc isdn switch-type primary-net5 isdn incoming-voice modem isdn bchan-number-order ascending no cdp enable ! interface Serial3/3:15 no ip address encapsulation hdlc isdn switch-type primary-net5 isdn incoming-voice modem isdn bchan-number-order ascending no cdp enable ! router rip redistribute connected network 10.0.0.0 network 192.168.101.0 ! ! ip route 192.168.101.0 255.255.255.0 192.168.101.110 ip route 192.168.105.0 255.255.255.0 192.168.101.210 no ip http server ! ! access-list 101 permit ip any any dialer-list 1 protocol ip permit snmp-server community public RO no cdp log mismatch duplex ! ! ! control-plane ! ! ! voice-port 3/0:D ! voice-port 3/1:D ! voice-port 3/2:D ! voice-port 3/3:D ! ! dial-peer cor list Any ! ! dial-peer voice 20 voip description Peering with HMP service session destination-pattern 2911600 session protocol sipv2 session target ipv4:10.10.12.2 dtmf-relay rtp-nte codec g711alaw no vad ! dial-peer voice 40 pots description Peering with the MSC destination-pattern [0-9] no digit-strip direct-inward-dial port 3/0:D forward-digits all ! dial-peer voice 50 pots description Peering with the MSC - 2nd E1 preference 1 destination-pattern [0-9] direct-inward-dial port 3/1:D forward-digits all ! dial-peer voice 60 pots description Peering with the MSC - 3rd E1 preference 2 destination-pattern [0-9] direct-inward-dial port 3/2:D forward-digits all ! dial-peer voice 70 pots description Peering with the MSC - 4th E1 preference 3 destination-pattern [0-9] direct-inward-dial port 3/3:D forward-digits all ! ! sip-ua registrar ipv4:10.10.12.2 expires 3600 sip-server ipv4:10.10.12.2 ! ss7 mtp2-variant Bellcore 0 ss7 mtp2-variant Bellcore 1 ss7 mtp2-variant Bellcore 2 ss7 mtp2-variant Bellcore 3 ! line con 0 logging synchronous stopbits 1 line aux 0 stopbits 1 line vty 0 4 password ****** login ! scheduler allocate 10000 400 end MOF_Uganda# MOF_Uganda# MOF_Uganda#debug isdn 9312 debug isdn q931 is &nbs p;ON. MOF_Uganda# ***************LOCAL CALL ... LOCAL CALLS WORK FINE****************** MOF_Uganda# MOF_Uganda# *May 30 16:20:19.303: ISDN Se3/0:15 Q931: RX <- ALERTING pd = 8 callref = 0x815A Progress Ind i = 0x8488 - In-band info or appropriate now available Progress Ind i = 0x8484 - Call has returned to the ISDN *May 30 16:20:20.215: ISDN Se3/3:15 Q931: RX <- SETUP pd = 8 callref = 0x00B7 Sending Complete Bearer Capability i = 0x8090A3 Standard = CCITT Transfer Capability = Speech Transfer Mode = Circuit Transfer Rate = 64 kbit/s Channel ID i = 0xA18381 Preferred, Channel 1 Facility i = 0x91A1130202008002010F300A0201010A0101A1028100 Protocol Profile = Remote Operations Protocol 0xA1130202008002010F300A0201010A0101A1028100 Component = Invoke component Invoke Id = 128 Operation = Diversion Leg2 Calling Party Number i = 0x00A3, N/A Plan:Unknown, Type:Unknown Called Party Number i = 0x81, '1999' Plan:ISDN, Type:Unknown *May 30 16:20:20.219: ISDN Se3/3:15 Q931: extract_redirect_orig_called_ie: IE type redirecting n MOF_Uganda#um none reason 15 cnt 1 plan -1 type 0 pres 1 *May 30 16:20:20.223: ISDN Se3/0:15 Q931: Applying typeplan for sw-type 0x12 is 0x0 0x0, Calling num *May 30 16:20:20.223: ISDN Se3/0:15 Q931: Applying typeplan for sw-type 0x12 is 0x0 0x1, Called num 1999 *May 30 16:20:20.223: ISDN Se3/3:15 Q931: TX -> CALL_PROC pd = 8 callref = 0x80B7 Channel ID i = 0xA98381 Exclusive, Channel 1 *May 30 16:20:20.223: ISDN Se3/0:15 Q931: TX -> SETUP pd = 8 callref = 0x015B Sending Complete Bearer Capability i = 0x8090A3 Standard = CCITT Transfer Capability = Speech Transfer Mode = Circuit Transfer Rate = 64 kbit/s Channel ID i = 0xA98383 Exclusive, Channel 3 Facility i = 0x91A1130202008002010F300A0201010A0101A1028100 Protocol Profile = Remote Operations Protocol 0xA1130202008002010F300A0201010A0101A1028100 Component = Invoke component Invoke Id = 128 Operation = Diversion Leg2 Calling Party Number i = 0x00A3, N/A Plan:Unknown, Type:Unknown Called Party Number i = 0x81, '1999' Plan:ISDN, Type:Unknown *May 30 16:20:20.251: ISDN Se3/0:15 Q931: RX <- CALL_PROC pd = 8 callref = 0x815B Channel ID i = 0xA98383 Exclusive, Channel 3 *May 30 16:20:20.255: ISDN Se3/0:15 Q931: RX <- ALERTING pd = 8 callref = 0x815B Progress Ind i = 0x8A88 - In-band info or appropriate now available Progress Ind i = 0x8A81 - Call not end-to-end ISDN, may have in-band info *May 30 16:20:20.255: ISDN Se3/3:15 Q931: TX -> ALERTING pd = 8 callref = 0x80B7 Progress Ind i = 0x8A88 - In-band info or appropriate now available Progress Ind i = 0x8A81 - Call not end-to-end ISDN, may have in-band info *May 30 16:20:22.263: ISDN Se3/0:15 Q931: RX <- DISCONNECT pd = 8 callref = 0x815B Cause i = 0x839F - Normal, unspecified *May 30 16:20:22.263: ISDN Se3/0:15 Q931: TX -> RELEASE pd = 8 callref = 0x015B *May 30 16:20:22.283: ISDN Se3/0:15 Q931: RX <- RELEASE_COMP pd = 8 callref = 0x815B *May 30 16:20:22.283: ISDN Se3/3:15 Q931: RX <- DISCONNECT pd = 8 callref = 0x00B7 Cause i = 0x809F - Normal, unspecified *May 30 16:20:22.283: ISDN Se3/3:15 Q931: TX -> RELEASE pd = 8 callref = 0x80B7 *May 30 16:20:22.287: ISDN Se3/3:15 Q931: Applying typeplan for sw-type 0x12 is 0x0 0x0, Calling num *May 30 16:20:22.287: ISDN Se3/3:15 Q931: Applying typeplan for sw-type 0x12 is 0x0 0x1, Called num 1999 *May 30 16:20:22.287: ISDN Se3/3:15 Q931: TX -> SETUP pd = 8 callref = 0x015C Sending Complete Bearer Capability i = 0x8090A3 Standard = CCITT Transfer Capability = Speech Transfer Mode = Circuit Transfer Rate = 64 kbit/s Channel ID i = 0xA98382 Exclusive, Channel 2 Facility i = 0x91A1130202008002010F300A0201010A0101A1028100 Protocol Profile = Remote Operations Protocol 0xA1130202008002010F300A0201010A0101A1028100 Component = Invoke component Invoke Id = 128 Operation = Diversion Leg2 Calling Party Number i = 0x00A3, N/A Plan:Unknown, Type:Unknown Called Party Number i = 0x81, '1999' Plan:ISDN, Type:Unknown *May 30 16:20:22.287: ISDN Se3/3:15 Q931: TX -> DISCONNECT pd = 8 callref = 0x015C Cause i = 0x809F - Normal, unspecified *May 30 16:20:22.303: ISDN Se3/3:15 Q931: RX <- RELEASE_COMP pd = 8 callref = 0x00B7 *May 30 16:20:22.311: ISDN Se3/3:15 Q931: RX <- RELEASE pd = 8 callref = 0x815C *May 30 16:20:22.311: ISDN Se3/3:15 Q931: TX -> RELEASE_COMP pd = 8 callref = 0x015C *May 30 16:20:22.915: ISDN Se3/0:15 Q931: Applying typeplan for sw-type 0x12 is 0x0 0x1, Calling num 0752291801 *May 30 16:20:22.919: ISDN Se3/0:15 Q931: Applying typeplan for sw-type 0x12 is 0x0 0x1, Called num 0753080646 *May 30 16:20:22.919: ISDN Se3/0:15 Q931: TX -> SETUP pd = 8 callref = 0x015D Bearer Capability i = 0x8090A3 Standard = CCITT Transfer Capability = Speech Transfer Mode = Circuit Transfer Rate = 64 kbit/s Channel ID i = 0xA98383 Exclusive, Channel 3 Calling Party Number i = 0x0180, '0752291801' Plan:ISDN, Type:Unknown Called Party Number i = 0x81, '0753080646' Plan:ISDN, Type:Unknown *May 30 16:20:22.951: ISDN Se3/0:15 Q931: RX <- CALL_PROC pd = 8 callref = 0x815D Channel ID i = 0xA98383 Exclusive, Channel 3 MOF_Uganda# MOF_Uganda# *May 30 16:20:27.511: ISDN Se3/0:15 Q931: RX <- ALERTING pd = 8 callref = 0x815D Progress Ind i = 0x8488 - In-band info or appropriate now available MOF_Uganda# *May 30 16:20:29.431: ISDN Se3/0:15 Q931: TX -> DISCONNECT pd = 8 callref = 0x015D Cause i = 0x8090 - Normal call clearing *May 30 16:20:29.451: ISDN Se3/0:15 Q931: RX <- RELEASE pd = 8 callref = 0x815D *May 30 16:20:29.451: ISDN Se3/0:15 Q931: TX -> RELEASE_COMP pd = 8 callref = 0x015D MOF_Uganda# MOF_Uganda# MOF_Uganda# MOF_Uganda# MOF_Uganda# MOF_Uganda# MOF_Uganda# MOF_Uganda# ************** INTERNATIONAL CALL ... AFTER 17-20 SECONDS THE CALL DROPS AND CANNOT ************** GO THROUGH ... THERE ARE NO RESTRICTIONS ON THE GSM SWITCH********** MOF_Uganda# MOF_Uganda# %Error opening tftp://255.255.255.255/network-confg (Timed out) *May 30 16:20:38.583: %SYS-4-CONFIG_RESOLVE_FAILURE: System config parse from (tftp://255.255.255.255/network-confg) failed MOF_Uganda# *May 30 16:20:41.603: ISDN Se3/0:15 Q931: Applying typeplan for sw-type 0x12 is 0x0 0x1, Calling num 0752291801 *May 30 16:20:41.603: ISDN Se3/0:15 Q931: Applying typeplan for sw-type 0x12 is 0x0 0x1, Called num 00027117044748 *May 30 16:20:41.603: ISDN Se3/0:15 Q931: TX -> SETUP pd = 8 callref = 0x015E Bearer Capability i = 0x8090A3 Standard = CCITT Transfer Capability = Speech Transfer Mode = Circuit Transfer Rate = 64 kbit/s Channel ID i = 0xA98383 Exclusive, Channel 3 Calling Party Number i = 0x0180, '0752291801' Plan:ISDN, Type:Unknown Called Party Number i = 0x81, '00027117044748' Plan:ISDN, Type:Unknown MOF_Uganda# *May 30 16:20:41.631: ISDN Se3/0:15 Q931: RX <- SETUP_ACK pd = 8 callref = 0x815E Channel ID i = 0xA98383 Exclusive, Channel 3 MOF_Uganda# *May 30 16:20:47.039: ISDN Se3/0:15 Q931: TX -> DISCONNECT pd = 8 callref = 0x015A Cause i = 0x8090 - Normal call clearing *May 30 16:20:47.063: ISDN Se3/0:15 Q931: RX <- RELEASE pd = 8 callref = 0x815A *May 30 16:20:47.063: ISDN Se3/0:15 Q931: TX -> RELEASE_COMP pd = 8 callref = 0x015A MOF_Uganda# *May 30 16:20:51.751: ISDN Se3/0:15 Q931: RX <- DISCONNECT pd = 8 callref = 0x815E Cause i = 0x839F - Normal, unspecified *May 30 16:20:51.751: ISDN Se3/0:15 Q931: TX -> RELEASE pd = 8 callref = 0x015E *May 30 16:20:51.771: ISDN Se3/0:15 Q931: RX <- RELEASE_COMP pd = 8 callref = 0x815E *May 30 16:20:51.775: ISDN Se3/3:15 Q931: Applying typeplan for sw-type 0x12 is 0x0 0x1, Calling num 0752291801 *May 30 16:20:51.775: ISDN Se3/3:15 Q931: Applying typeplan for sw-type 0x12 is 0x0 0x1, Called num 00027117044748 MOF_Uganda# *May 30 16:20:51.775: ISDN Se3/3:15 Q931: TX -> SETUP pd = 8 callref = 0x015F Bearer Capability i = 0x8090A3 Standard = CCITT Transfer Capability = Speech Transfer Mode = Circuit Transfer Rate = 64 kbit/s Channel ID i = 0xA98381 Exclusive, Channel 1 Calling Party Number i = 0x0180, '0752291801' Plan:ISDN, Type:Unknown Called Party Number i = 0x81, '00027117044748' Plan:ISDN, Type:Unknown *May 30 16:20:51.811: ISDN Se3/3:15 Q931: RX <- SETUP_ACK pd = 8 callref = 0x815F Channel ID i = 0xA98381 Exclusive, Channel 1 MOF_Uganda# *May 30 16:20:54.711: ISDN Se3/0:15 Q931: TX -> DISCONNECT pd = 8 callref = 0x0158 Cause i = 0x8090 - Normal call clearing *May 30 16:20:54.731: ISDN Se3/0:15 Q931: RX <- RELEASE pd = 8 callref = 0x8158 *May 30 16:20:54.731: ISDN Se3/0:15 Q931: TX -> RELEASE_COMP pd = 8 callref = 0x0158 MOF_Uganda# %Error opening tftp://255.255.255.255/cisconet.cfg (Timed out) *May 30 16:20:59.811: %SYS-4-CONFIG_RESOLVE_FAILURE: System config parse from (tftp://255.255.255.255/cisconet.cfg) failed MOF_Uganda# *May 30 16:21:02.751: ISDN Se3/3:15 Q931: RX <- DISCONNECT pd = 8 callref = 0x815F Cause i = 0x839F - Normal, unspecified *May 30 16:21:02.751: ISDN Se3/3:15 Q931: TX -> RELEASE pd = 8 callref = 0x015F *May 30 16:21:02.771: ISDN Se3/3:15 Q931: RX <- RELEASE_COMP pd = 8 callref = 0x815F MOF_Uganda# *May 30 16:21:04.955: ISDN Se3/0:15 Q931: Applying typeplan for sw-type 0x12 is 0x0 0x1, Called num 0392961806 *May 30 16:21:04.955: ISDN Se3/0:15 Q931: TX -> SETUP pd = 8 callref = 0x0160 Bearer Capability i = 0x8090A3 Standard = CCITT Transfer Capability = Speech Transfer Mode = Circuit Transfer Rate = 64 kbit/s Channel ID i = 0xA98381 Exclusive, Channel 1 Called Party Number i = 0x81, '0392961806' Plan:ISDN, Type:Unknown *May 30 16:21:04.991: ISDN Se3/0:15 Q931: RX <- CALL_PROC pd = 8 callref = 0x8160 Channel ID i = 0xA98381 Exclusive, Channel 1 MOF_Uganda# *May 30 16:21:05.191: ISDN Se3/0:15 Q931: RX <- ALERTING pd = 8 callref = 0x8160 Progress Ind i = 0x8A88 - In-band info or appropriate now available Progress Ind i = 0x8A81 - Call not end-to-end ISDN, may have in-band info MOF_Uganda# MOF_Uganda# MOF_Uganda#no debug *May 30 16:21:08.311: ISDN Se3/0:15 Q931: TX -> DISCONNECT pd = 8 callref = 0x0160 Cause i = 0x8090 - Normal call clearing *May 30 16:21:08.331: ISDN Se3/0:15 Q931: RX <- RELEASE pd = 8 callref = 0x8160 *May 30 16:21:08.331: ISDN Se3/0:15 Q931: TX -> RELEASE_COMP pd = 8 callref = 0x0160 MOF_Uganda#no debug all All possible debugging has been turned off MOF_Uganda# MOF_Uganda# ------------- Bishop(TCP/IP), CCNP |
Replies:
Posted by: Headhunter
Date Posted: 10 July 2007 at 12:27am
| Callmanager setup correctly? QSIG working OK? ------------- Koen CCSI#30501 CCNP CCIP CCVP CCSP CCDP CQS-Cisco Wireless LAN Design & Support Cisco Unity Design Specialist Cisco IP Telephony Design Specialist JNCIA-ER MCSE MCSA:Messaging |
Posted by: hudsonmbg
Date Posted: 10 July 2007 at 7:10am
We are not using Cisco Call Manager. What is happening is that I have 4 x E1`s connected to the Gateway, local calls works fine but as soon as I want to dial international I get a 10-20 second delay then the call is disconnected, our provider ensures me that there are no restrictions on the E1, and they suggest that we send a "F" as a indicator that the number is completed so the GSM Switch can process the request, at the moment the GSM Switch awaits for more digits and then times out. Some guy said we look closely at the compression being used. ------------- Bishop(TCP/IP), CCNP |
Posted by: Headhunter
Date Posted: 10 July 2007 at 7:18am
| mmm *May 30 16:20:54.711: ISDN Se3/0:15 Q931: TX -> DISCONNECT pd = 8 callref = 0x0158 Cause i = 0x8090 - Normal call clearing ------------- Koen CCSI#30501 CCNP CCIP CCVP CCSP CCDP CQS-Cisco Wireless LAN Design & Support Cisco Unity Design Specialist Cisco IP Telephony Design Specialist JNCIA-ER MCSE MCSA:Messaging |
Posted by: hudsonmbg
Date Posted: 11 July 2007 at 1:56am
| Thanks man. I just googled that message and the problem is currently being solved. ------------- Bishop(TCP/IP), CCNP |
Posted by: c r d
Date Posted: 15 July 2007 at 12:57pm
Why are you posting real world Cisco problems in the CCIE section? It has nothing to do with CCIE certification, other than you being fond of this section  ------------- MCSE/MCSA:Security|Messaging, MCDST, MCTS:Vista/Office 2007, MCITP:Vista Enterprise Support, A+, Network+, CCNP, CWSP, GCWN, GCUX, CISSP |
Posted by: Headhunter
Date Posted: 16 July 2007 at 9:24am
| Mmm CRD is right.... if the problem is from a problem at work then it's Cisco real world, if it has something to do with the written or lab exam it goes in CCIE ------------- Koen CCSI#30501 CCNP CCIP CCVP CCSP CCDP CQS-Cisco Wireless LAN Design & Support Cisco Unity Design Specialist Cisco IP Telephony Design Specialist JNCIA-ER MCSE MCSA:Messaging |